LQD Device - HOW TO


GET STARTED

FILL THE TANK

CLEAN THE TANK

CHARGE

REPLACE THE ATOMISER

If the device is fully-charged, but stops producing vapour, the atomiser needs to be replaced. Replacement atomisers are available to buy in packs of 3.

●●●  Step 1

With your new atomiser add 8 drops of the Logic LQD E-Liquid in each semi-circular hole located on the top of the atomiser to lubricate the cotton inside.

●●●  Step 2

Ensure that the mouthpiece is screwed onto the tank. Hold the device upside down. Unscrew the battery from the atomiser, and then unscrew the atomiser from the tank, being careful to prevent spilling, and discard.

●●●  Step 3

Screw the new atomiser onto the tank, and then screw on the battery.

●●●  Step 4

Shake the device for 10 seconds, and wait 3 minutes before pressing the activation button.

●●●  Step 1

Insert the charger cable into the micro USB port located on the bottom side of the battery.

●●●  Step 2

Insert the USB Charger into any compatible USB port. The activation button will flash 3 times to indicate that charging has begun.

The light will glow in different colours as charging progresses:
Red – Low
Orange – Medium
Green – High
No Glow – Fully-Charged

●●●  Step 3

Unplug the device once it’s fully-charged.

It’s a good idea to clean out your tank every time you switch flavours or replace your atomiser to prevent build-up and keep the device in good working order.

●●●  Step 1

Ensure the mouthpiece is tightly screwed onto the tank to ensure that the e-liquid path is open. Hold the device upside-down, and unscrew the tank from the atomiser to avoid potential leakage.

●●●  Step 2

Fill the tank with water through the underside of the tank. Use your finger to cover the bottom side of the tank and then shake.

●●●  Step 3

Turn the tank over so that water will fall from the bottom end of the tank.

●●●  Step 4

Repeat steps 2 and 3 a few times to ensure that the tank is cleaned. Wait until the tank dries, and then reassemble the device. Wash your hands with soap and water.

Remember: It’s important to repeat the process of adding drops of e-liquid to the atomiser every time you replace the atomiser and after long periods of disuse. Only refill the tank when attached to the atomiser to avoid potential leakage.

●●●  Step 1

Unscrew the mouthpiece from the fully assembled device.

●●●  Step 2

Insert the nozzle of the Logic E-liquid bottle through the white silicone barrier of the refillable tank. Fill the tank to the desired level, do not exceed the white silicone seal. When filled, screw the mouthpiece onto the tank.

Logic LQD vapouriser comes charged and ready to use. But there are a few important steps you need to remember when filling and using a brand new Logic LQD tank.

●●●  Step 1

When filling the tank for the first time, add 8 drops of the Logic LQD E-Liquid in each semi-circular hole located on the top of the atomiser to lubricate the cotton inside. It’s important that you also do this every time you replace the atomiser, or if the device hasn’t been used for a long period of time.

●●●  Step 2

When you are ready to fill your tank with e-liquid follow the step by step guide here.

●●●  Step 3

After filling the tank and reassembling the device, shake it for 10 seconds and then wait 3 minutes before pressing the activation button.

●●●  Step 4

Press the activation button 5x within 2 seconds to activate the device, and simply press and hold to vape. Press and hold up or down on the button to vary the device’s voltage.

LOGIC LQD – THE COMPONENTS


MouthpieceUnscrew the mouthpiece to refill the tank and clean the mouthpiece itself.

LOGIC LQD tank2ml refillable tank specially designed with Logic LQD E-Liquid bottles for precision, easy filling.

activation button Press the activation button 5x within 2 seconds to activate or deactivate the device. Simply press and hold the button to vape.

Rechargeable battery 650 mAh battery with a soft-touch finish.

micro usb charger port

Silicone seal Silicone seal to prevent leaks.

atomiser 1.7-1.9 ohm replaceable dual-coil atomiser.

battery indicator The LED light will change colour from red to orange to green as charging progresses. The light will stop glowing when the device is fully-charged.

variable voltage The device has 2 different voltage settings – low and high – so you can vape according to your preference. Press and hold the top part of the activation button to use high voltage mode (4.2V) or the bottom part of the button to use low voltage mode (3.6 V). The higher the voltage, the stronger the vape.

+
Mouthpiece

Unscrew the mouthpiece to refill the tank and clean the mouthpiece itself.
+
Silicone seal

Silicone seal to prevent leaks.
+
LOGIC LQD tank

2ml refillable tank specially designed with Logic LQD E-Liquid bottles for precision, easy filling.
+
atomiser

1.7-1.9 ohm replaceable dual-coil atomiser.
+
battery indicator

The LED light will change colour from red to orange to green as charging progresses. The light will stop glowing when the device is fully-charged.
+
variable voltage

The device has 2 different voltage settings – low and high – so you can vape according to your preference. Press and hold the top part of the activation button to use high voltage mode (4.2V) or the bottom part of the button to use low voltage mode (3.6 V). The higher the voltage, the stronger the vape.
+
activation button

Press the activation button 5x within 2 seconds to activate or deactivate the device. Simply press and hold the button to vape.
+
Rechargeable battery

650 mAh battery with a soft-touch finish.
+
micro usb charger port